83.060 (Rubber) 标准查询与下载

ASTM D3346-03 橡胶特性的标准试验方法.用门尼粘度计测定SBR(丁苯橡胶)的加工性能

These empirical tests have been found to be suitable for ranking a series of unpigmented emulsion SBR in order of processability. They may also be used for comparing a production lot with a standard of known processability characteristics. The difference between Mooney viscosities at two specified times will rank those emulsion SBR polymers that differ appreciably in this property according to their processability. The actual values obtained for a given polymer depend on whether or not the sample was massed, and may vary between laboratories or with the type of machine used, and with the specified times at which Mooney viscosity values were taken.1.1 These test methods178; explain the use of the shearing disk viscometer to obtain an indication of the processability of non-pigmented emulsion styrene-butadiene rubbers (SBR). They may also be used to separate those polymers that are easy to process from those that are difficult to process within a group of polymers of the same type.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Rubber Property8212;Processability of Emulsion SBR (Styrene-Butadiene Rubber) With the Mooney Viscometer (Delta Mooney)

ASTM D3566-03 橡胶的标准实施规程.用氧燃烧法测定在氯存在时橡胶中的溴含量

This practice outlines a method for the determination of bromine and chlorine, alone or together. CIIR and BIIR rubbers contain small amounts of chlorine and bromine and CR rubbers contain large amounts of chlorine. For quality control and research and development, it is sometimes necessary to determine the amount of these halogens in rubber. This practice can be used for these purposes.1.1 This practice covers the determination of bromine and chlorine in rubber.1.2 This procedure is applicable to raw or cured NR, SBR, BR, IR, IIR, CIIR, BIIR, and EPDM rubbers and blends of these.1.3 Iodine interferes, but substances such as Zn 2+, S, CN, and (CO3)2 do not.1.4 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific safety precautions are given in Section 7.

Standard Practice for Rubber8212;Determination of Bromine in the Presence of Chlorine by Oxygen Combustion

ASTM D3848-03(2013) 碳黑混合的NBR(丙烯腈共聚物橡胶)橡胶评估的标准试验方法

3.1 These test methods are mainly intended for referee purposes but may be used for quality control of rubber production. They may also be used in research and development work and for comparison of different samples in a standard test formula. 3.2 These test methods may also be used to obtain values for customer acceptance of rubber. 1.1 These test methods specify the standard materials, test formula, mixing procedures, and test methods for the evaluation of acrylonitrile-butadiene rubber (NBR) mixed with carbon black. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Rubbermdash;Evaluation of NBR 40;Acrylonitrile-Butadiene Copolymers41; Mixed With Carbon Black

ASTM D6909-03 碳氟三元共聚物合成橡胶耐高温和耐酸的标准规范

1.1 This specification covers requirements for the fluorocarbon terpolymer elastomer used in the manufacture of expansion joints for use in coal-fired utilities and other high temperature industrial applications in which corrosive flue gases are present.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.1.3 This specification is intended as a reference procedure for evaluating the performance of these vulcanizates and can also be used for quality assurance testing before release of a lot based on agreement between supplier and purchaser.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for High Temperature and Acid-Resistant Fluorocarbon Terpolymer Elastomer

ASTM D1229-03(2008) 橡胶特性.在低温时压缩率的标准试验方法

Rubber products, such as hydraulic seals on aircraft, submarine hatch gaskets, and hydraulic brake cups, may be exposed to varying temperature extremes. This test method provides a means of determining the extent to which recovery from compression at normal ambient temperatures is inhibited upon release of the compressive force during subsequent exposure at low temperatures.1.1 This test method covers evaluation of the ability of vulcanized rubbers that have been compressed at room temperature and then subjected to low temperature (air or carbon dioxide atmosphere), to recover from deformation when taken from the clamping device while still at the low temperature.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property-Compression Set at Low Temperatures

ASTM D3568-03(2009) 橡胶的标准试验方法:评价包括与油混合的EPDM(三聚乙丙橡胶)的标准试验方法

These test methods are intended mainly for referee purposes but may be used for quality control of rubber production. They may also be used in research and development work and for comparison of different rubber samples in a standard formula. These test methods may be used to obtain values for customer acceptance of rubber.1.1 These test methods specify the standard materials, test formulas, mixing procedures, and test methods for the evaluation and production control of ethylene propylene diene rubbers (EPDM). 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Rubber8212;Evaluation of EPDM (Ethylene Propylene Diene Terpolymers) Including Mixtures With Oil

ASTM D3568-03 橡胶的标准试验方法.包括与油混合的EPDM(三聚乙丙橡胶)的评估

These test methods are intended mainly for referee purposes but may be used for quality control of rubber production. They may also be used in research and development work and for comparison of different rubber samples in a standard formula. These test methods may be used to obtain values for customer acceptance of rubber.1.1 These test methods specify the standard materials, test formulas, mixing procedures, and test methods for the evaluation and production control of ethylene propylene diene rubbers (EPDM). 1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Rubber8212;Evaluation of EPDM (Ethylene Propylene Diene Terpolymers) Including Mixtures With Oil

ASTM D1229-03 橡胶特性的标准试验方法.低温时的压缩形变

Rubber products, such as hydraulic seals on aircraft, submarine hatch gaskets, and hydraulic brake cups, may be exposed to varying temperature extremes. This test method provides a means of determining the extent to which recovery from compression at normal ambient temperatures is inhibited upon release of the compressive force during subsequent exposure at low temperatures.1.1 This test method covers evaluation of the ability of vulcanized rubbers that have been compressed at room temperature and then subjected to low temperature (air or carbon dioxide atmosphere), to recover from deformation when taken from the clamping device while still at the low temperature. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property8212;Compression Set at Low Temperatures

ASTM D3566-03(2009) 用氧燃烧法测定在氯存在时橡胶中的溴含量的标准实施规程

This practice outlines a method for the determination of bromine and chlorine, alone or together. CIIR and BIIR rubbers contain small amounts of chlorine and bromine and CR rubbers contain large amounts of chlorine. For quality control and research and development, it is sometimes necessary to determine the amount of these halogens in rubber. This practice can be used for these purposes.1.1 This practice covers the determination of bromine and chlorine in rubber. 1.2 This procedure is applicable to raw or cured NR, SBR, BR, IR, IIR, CIIR, BIIR, and EPDM rubbers and blends of these. 1.3 Iodine interferes, but substances such as Zn2+, S, CN−, and (CO3)2 − do not. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific safety precautions are given in Section 7.

Standard Practice for Rubber8212;Determination of Bromine in the Presence of Chlorine by Oxygen Combustion

ASTM D429-03e1 相互比较渗透管以确定示踪能力的标准指南

These test methods are designed primarily for specimens prepared in a laboratory under standardized conditions such as may be used to provide data for development and control of rubber compounds and methods of manufacture. With slight modifications as indicated, Methods A, B, C, D, and E are also used for obtaining comparative adhesion test values of production parts whenever the design permits preparation of suitable test specimens. Methods A, B, C, and D are applicable in the case of many products in which rubber is used for controlling vibration.1.1 These test methods cover procedures for testing the static adhesional strength of rubber to rigid materials (in most cases metals).Method A8212;Rubber Part Assembled Between Two Parallel Metal Plates.Method B8212;90o Stripping Test-Rubber Part Assembled to One Metal Plate.Method C8212;Measuring Adhesion of Rubber to Metal with a Conical Specimen.Method D8212;Adhesion Test-Post-Vulcanization (PV) Bonding of Rubber to Metal.Method E8212;90 Stripping Test-Rubber Tank Lining-Assembled to One Metal Plate.Method F8212;Rubber Part Assembled Between Two Parallel Convex-Shaped Metal PlatesMethod G8212;Measuring Bond Durability for Rubber-to-Metal Bonded Components with a Double Shear Cylindrical SpecimenMethod H8212;Measuring Bond Durability for Rubber-to Metal Bonded Components with a Quadruple Shear Cylinder Speciment1.2 While the test method may be used with a wide variety of rigid materials, use of materials other than metals is the exception. For this reason, we have used the word "metal" in the text rather than "rigid materials."1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Rubber Property8212;Adhesion to Rigid Substrates

ASTM D3848-03(2009) 碳黑混合的NBR(丙烯腈共聚物橡胶)橡胶评估的标准试验方法

These test methods are mainly intended for referee purposes but may be used for quality control of rubber production. They may also be used in research and development work and for comparison of different samples in a standard test formula. These test methods may also be used to obtain values for customer acceptance of rubber.1.1 These test methods specify the standard materials, test formula, mixing procedures, and test methods for the evaluation of acrylonitrile-butadiene rubber (NBR) mixed with carbon black. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Rubber8212;Evaluation of NBR (Acrylonitrile-Butadiene Copolymers) Mixed With Carbon Black

ASTM D3848-03 橡胶的标准试验方法.与碳黑混合的NBR(苯烯腈-丁二烯共聚物)的评定

These test methods are mainly intended for referee purposes but may be used for quality control of rubber production. They may also be used in research and development work and for comparison of different samples in a standard test formula. These test methods may also be used to obtain values for customer acceptance of rubber.1.1 These test methods specify the standard materials, test formula, mixing procedures, and test methods for the evaluation of acrylonitrile-butadiene rubber (NBR) mixed with carbon black.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Rubber8212;Evaluation of NBR (Acrylonitrile-Butadiene Copolymers) Mixed With Carbon Black

ASTM D3767-03(2008) 橡胶尺寸的测量的标准实施规程

Dimensional measurements specified in this practice are made for one of the following purposes: (1) to determine conformance with specification requirements regarding geometrical properties of whole units, such as the size of rubber gloves, or the diameter and circumference of rubber hose, (2) to determine conformance with specification requirements regarding particular functional parts of units, such as the thickness of the soles of boots, or (3) to determine geometrical values that are necessary in the calculation of test results for physical properties for which requirements are specified, such as the thickness of a test specimen for tensile strength. The method to be used shall be as specified in the detail specification or appropriate test method. Pressure applied by measuring instruments has a significant effect on the observed thickness of soft flexible materials, and it is therefore necessary to specify the pressure imposed by the foot of the instrument on the test piece for accurate comparative measurements of such materials.1.1 This practice is intended for use in determining the geometrical dimensions of rubber products and specimens for physical tests. This practice describes procedures for determining length, width, thickness, diameter, and circumference. This practice does not cover sampling of materials or products, or locations where a sample is to be taken. 1.2 The values stated in either acceptable metric units or in other units shall be regarded separately as a standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any other way. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability or regulatory limitations prior to use.

Standard Practice for Rubberx2014;Measurement of Dimensions

ASTM D5044-02 橡胶化学制品苯并噻唑基二硫化物(MBTS)中游离2-硫醇苯并噻唑(MBT)的标准试验方法

1.1 This test method describes the procedure for estimation of the chloroform-soluble, acidic impurities in benzothiazyl disulfide (MBTS). 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Chemicals-Free 2-Mercaptobenzothiazole (MBT) in Benzothiazyl Disulfide (MBTS)

ASTM D4570-02 橡胶化学制品的标准试验方法.用筛分法(干法)测定硫的粒度

This test method is used to evaluate sulfur for suitability as a rubber vulcanizing agent. Sulfur particles must be small enough to dissolve in rubber during cure to produce a uniform network of cross-links. This test method is used as a quality control method to ensure that large particles are not present (and to determine if the sulfur follows a typical pattern for size distribution).1.1 This test method covers the particle size measurement of the coarse fraction of ground sulfurs. It is limited to measurement of particles greater than 45 956;m (No. 325 sieve). If the sulfur is very fine and the screens become plugged by the caking of the sulfur, it may be necessary to use a wet sieve procedure instead.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Chemicals8212;Determination of Particle Size of Sulfur by Sieving (Dry)

ASTM C1523-02a 预硫化弹胶接缝剂的模量,撕裂和粘结性能测定的标准试验方法

1.1 This test method describes a laboratory procedure for measuring modulus, tear, joint movement ability and adhesion properties of applied, Precured Elastomeric Joint Sealants, hereinafter referred to as "applied seal" and if not applied, hereinafter referred to as "seal," on portland cement mortar as a standard substrate and or other substrates. It tests these properties after dry, wet, frozen, heat aged or artificially weather-aged conditionings, or both.1.2 The values stated in SI units are to be regarded as the standard. Other values given in parentheses are provided for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.4 The committee with jurisdiction over this standard is not aware of any similar standard published by another committee or organization.

Standard Test Method for Determining Modulus, Tear and Adhesion Properties of Precured Elastomeric Joint Sealants

ASTM D6284-02(2008)e1 可溶于氯和氯胺液态溶剂的橡胶性能-效果的标准试验方法

Rubber articles, such as seals, gaskets, and membranes, may be exposed in service to chlorine compounds used in potable water as disinfectants. The exposure may be intermittent or continuous and can occur at various temperatures. Properties of rubber articles can deteriorate as a result of exposure to water containing these chlorine compounds, affecting their performance for the intended use. This test method attempts to simulate service conditions through controlled accelerated testing, but may not give a direct correlation with part performance under actual service conditions. It yields comparative data on which to base judgement on expected service quality. This test method is suitable for compliance testing, quality control, and research and development work.1.1 This test method covers procedures for evaluating the ability of rubber and rubber-like materials to withstand the effects of aqueous solutions with available chlorine and chloramine. It is intended to compare the effects of chlorine compounds, present in potable water due to disinfection procedures, on rubber articles. 1.2 Test solutions are designed to contain chlorine compounds, including hypochlorous acid (HOCI), hypochlorite ions (OCI), and monochloramine (NH2Cl). 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Property8212;Effect of Aqueous Solutions with Available Chlorine and Chloramine

ASTM D2229-02 钢轮胎帘线和橡胶之间粘结性的标准试验方法

1.1 This test method covers the determination of the force required to pull a steel cord from a block of vulcanized rubber.1.2 Although designed primarily for steel cord, this test method may be applied with modifications to wire used in rubber products.1.3 This test method can also be used for evaluating rubber compound performance with respect to adhesion to steel cord.1.4 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Adhesion Between Steel Tire Cords and Rubber

ASTM D5051-02 橡胶化学制品苯并噻唑基二硫化物(MBTS)的标准试验方法.分析

1.1 This test method describes the determination of assay of benzothiazyl disulfide (MBTS). It is based on a titration of free iodine liberated upon reduction of MBTS, with potassium iodide (KI) in acid medium. 1.2 The assay is determined as mass percent. 1.3 Free 2-mercaptobenzothiazole (MBT) content is not determined. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Rubber Chemicals-Benzothiazyl Disulfide (MBTS)-Assay

ASTM D3183-02 用橡胶制品制备试验用的橡胶试片的标准实施规程

1.1 This practice describes methods for the preparation of pieces of a rubber vulcanizate that is not in the form of sheet. Such pieces are used as a source from which specimens are obtained for testing.1.2 The values stated in SI units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Rubber8212;Preparation of Pieces for Test Purposes from Products